Influence of Thermomechanical Processing Parameters on the Mechanical Properties of an Aluminum Alloy used in Cutting-Edge Technique

  • Marian-Iulian NEACȘU "Dunarea de Jos" University of Galati, Romania
Keywords: aluminum alloy, thermomechanical processing, mechanical properties

Abstract

Special aluminum alloys are mainly used in the aeronautical and machinebuilding industries, areas of technique where materials must possess superior mechanical properties. These properties are obtained as a result of special methods of elaboration and subsequent processing. The special properties of these alloys are also influenced by the alloying elements present in their chemical composition. In this paper it is studied the way in which the parameters of the thermomechanical treatment process applied to an aluminum alloy influence the mechanical properties of the studied alloys. Thermomechanical processing consists of solution hardening, cold plastic deformation and artificial ageing at different temperatures and various times of maintenance at these temperatures.

Creative Commons License

Downloads

Download data is not yet available.

References

[1]. Dragomir I., et al., Conductibilitatea electrică a unor zguri utilizate la retopirea electrică sub zgură, in Metalurgia, nr. 10, p. 505, 1987.
[2]. Ienciu M., Moldovan P., et al., Rafinarea fizică a aliajelor prin filtrare în stare lichidă, Metalurgia, nr. 6, p. 287, 1989.
[3]. Deschamps A., Fribourg G., Brechet Y., Chemin J. L., Hutchinson C. R., In situ evaluation of dynamic precipitation during plastic straining of an Al–Zn–Mg–Cu alloy, Acta Materialia, vol. 60, issue 5, p. 1905-1916, March 2012.
[4]. Hutchinson C. R., de Geuser F., Chen Y., Deschamps A., Quantitative measurements of dynamic precipitation during fatigue of an Al–Zn–Mg–(Cu) alloy using small-angle X-ray scattering, Acta Materialia, vol. 74, p. 96-109, 2014.
[5]. Marluad T., Deschamps A., Bley F., Lefebvre W., Baroux B., Acta Materialia, vol. 58, issue 14, p. 4814-4826, August 2010.
[6]. Drugescu E., Ştiinţa materialelor metalice, Galaţi, 2001.
[7]. Dumitrescu C., Şaban R., Metalurgie fizică-Tratamente termice, Editura Fair Partners, Bucuresti, 2001.
[8]. Gâdea S., Petrescu M., Metalurgie fizică şi studiul metalelor, vol. I, II and III, Editura Didactică şi Pedagogică, Bucureşti, 1983.
[9]. Giacomelli I., Aspecte privind unele procedee de îmbătrânire accelerată a aliajelor de aluminiu pentru turnare, revista Construcţia de Maşini, nr. 8, 1992.
[10]. Ursulache M., Proprietăţile metalelor, Editura Didactică şi Pedagogică, Bucureşti, 1982.
[11]. Petrescu M. et al., Thermodynamics and structure in materials science, Departament of engineering sciences, Editura Politehnica University, Bucharest, 1996.
[12]. ***, Aluminium Asociation - SR-EN 485/2/2007 – Aluminium and aluminium Alloys - Sheet strip and plate - Mechanical Properties.
Published
2019-12-15
How to Cite
1.
NEACȘU M-I. Influence of Thermomechanical Processing Parameters on the Mechanical Properties of an Aluminum Alloy used in Cutting-Edge Technique. The Annals of “Dunarea de Jos” University of Galati. Fascicle IX, Metallurgy and Materials Science [Internet]. 15Dec.2019 [cited 7Oct.2024];42(4):8-3. Available from: https://www.gup.ugal.ro/ugaljournals/index.php/mms/article/view/2812
Section
Articles

Most read articles by the same author(s)